Printer Care and cleaning

The printer is very sensitive to damage if we can not take care of and cleaned properly and regularly. Here are some tips you can do to treat and clean the printer to be more durable.

A. Each cleaning the printer, make sure the printer is really in a state of death and no cables connected to either the electrical or computer.
B. Use non-flammable solution to clean on the printer.
C. To clean the head manually, you should use a clean soft cloth and do the scrub on the head slowly.
D. At a certain time, use the command "head cleaning" software contained on the properties of each printer to clean the printer head from the ink spread or spilled.
E. Use quality carbon ribbon, ink, or toner is good because it will affect the quality and age of the printer.
F. Do not ever make changes or modifications that do not conform to the printer as some parts of the printer contain high-voltage components.
G. Never put objects, such as iron, condensation, or food on the printer because if it falls into the printer, it will cause damage to some important components.

»»  read more

RAM Memory Care

After the previous post, I discussed about the problems that occurred in RAM, so on this occasion I will give you tips on how to care for the RAM to make it more durable.
Here are some points that can be noticed in the treatment of computer RAM.

1. Avoid over clocking action if the computer does not support for the over clock.
2. Keep the temperature stable computer with install more fans inside the casing and a good computer.
3. Use a memory from vendors who have proven good quality.
4. Use a memory with the capacity and relevant PC applications that will be used to work so that the computer does not happen often hangs.

»»  read more

Troubleshooting on Processor and its Maintenance

Problems on the processor generally cause the appearance of the layer blank without any sound. This occurs because:
1. Processors dead or damaged.
2. The processor temperature is too hot burns caused due to over clock or because the processor fan is not working.
The solution is to replace a new processor.

Processor Maintenance
The treatment for computer processors are:
1. Use a good heat sink and fan.
2. Frequently clean the heat sink and fan attached to the processor.
3. Trim the cable is in the casing.
4. Avoid doing the technique is not easy to over clock the processor to heat and age, the processor can be longer.

»»  read more

Monitor cleaning and maintenance

In previous posts I have discussed how knowing the damage indicator on the monitor, and the opportunity this time, I will discuss how to perform maintenance and cleaning of the monitor so that the possibility of damage could be mitigated and controlled. Here are some steps you can do:

a. Screen and casing should be frequently cleaned from the dust that often occupy and stack that caused the screen looks dirty and unclear. Use a soft cloth. If necessary, use a special fluid to the tube or LCD screen.

b. To prevent premature failure of power supply on the monitor, use power-management features in the display properties sheet or power management to monitor the condition of low-power standby mode after a period (between 10-15 minutes) and metikan after 60 minutes. Use of this feature is much better than using a switch ON / OFF if the computer will be left for a moment.

c. Ensure adequate ventilation the monitor to get on the side, rear, and up, because the monitor uses only passive cooling. Lack of air flow will affect the life of the monitor.

d. Keep monitoring the position of objects that contain magnets, such as speakers.

e. Keep out of reach of children and avoid the monitor not to get wet.

»»  read more

Power supply & cassing Care

Care to extend power supply, among others:

1. Use a good stabilizer or UPS.
The use of the stabilizer, aims to keep the voltage received by the power supply remains stable. Many electronic devices damage caused by unstable voltage. Recommended for use or stabilizer which uses servo motors, and if there are no funds, we recommend using UPS.

2. Do not put the casing around the air vents.
Air circulation in the room who came in through the air vents usually carry moist air. This can cause the temperature around the casing to be moist. When moist will cause the legs of electronic components (especially IC) became rusted and finally a brief relationship occurred between the components that cause the fire.

3. Cleaning the dust (dirt) is in the power supply and chassis.
Dirt on the power supply and chassis fan sometimes causing jams or does not rotate. This can cause the power supply and hardware components inside the casing to heat faster and will cause the computer to die a sudden and do not work until the temperature inside the casing back to normal.

4. Add the fan inside the casing.
Additional fan in the casing will accelerate the air circulation inside the casing so that the computer is not fast heat and hardware components in it can work well.

To see the symptoms of damage to the power supply, please click here.

»»  read more